Current position > Product detail
『Air Flow Meter Manufacturers: Global Industrial Gas Sourcing Portal』Related information(clamp on meter|electromagnetic meter|venturi meterrotameter|orifice meter|ultrasonic flow meter|mass flow meter|coriolis mass flow meter|coriolis flow meter|magnetic flow meter|magmeter flow meter|magflow flow meter|mag meter flow meter|electromagnetic flow meter|vortex flow meter|turbine flow meter|thermal mass flow meter|thermal flow meter|rotameter flow meter)
Air Flow Meter Manufacturers: Global Industrial Gas Sourcing Portal and Practical Selection
Quick Answer: Air flow meter sourcing gets faster when you specify gas type, line pressure, temperature, pipe diameter, and flow range before contacting a manufacturer. Silver Automation Instruments supplies thermal mass and vortex flow meters for compressed air, nitrogen, CO2, biogas, and steam. Send your pressure (bar), temperature (°C), pipe size (DN), and flow range to get a budget quote with technical selection within 24 hours.
Most buyers start with a model number and then call three suppliers. In practice, that approach backfires because gas density, moisture, and operating pressure change the meter output. A meter sized for 2 bar air will read wrong on 9 bar compressed air if the supplier does not apply pressure correction. For this reason, we ask for real process data before quoting. Asking for gas data is not a delay tactic. That step stops you from buying a meter that passes bench tests but fails in the field.
Many air flow meter manufacturers on a global industrial gas sourcing portal look similar. They list DN15 to DN300, 4-20 mA HART, and ATEX options. But the commercial difference shows up later. Buyers in Vietnam, Mexico, Saudi Arabia, and Indonesia often ask us to correct a meter selection from another source because the original supplier used ideal gas assumptions. For wet biogas or saturated compressed air, that assumption creates a 10 percent to 20 percent reading error.
Thermal mass flow meters for compressed air and low flow gas
Thermal mass flow meters work well for compressed air, nitrogen, CO2, and argon at pressures up to 40 bar. We supply inline and insertion types. Inline meters start at DN15. Insertion probes cover DN80 to DN300. The output options are 4-20 mA HART, RS485 Modbus, and pulse. Accuracy is around plus or minus 1.5 percent of reading for gas flows above 5 Nm3/h depending on the line size.
We have seen this on customer sites many times. A food packaging plant in Vietnam ran four compressed air lines at 8 bar and needed per-line consumption data. The plant used thermal mass insertion meters on DN80 pipes and cut air leakage by 18 percent after two months because the meters showed which shifts used the most air during idle periods.
For low flow applications, specify the minimum and maximum flow in Nm3/h or kg/h. Do not send only the compressor capacity. Compressor free air delivery is not the same as the actual per-line consumption. A 75 kW compressor can feed multiple branches with very different flow rates.
Vortex flow meters for steam, saturated gas, and high flow compressed air
Vortex meters handle steam, saturated gas, and compressed air flows where velocity is above 5 m/s. We offer flange connections from DN25 to DN200, with temperature ratings up to 350 °C and pressure ratings up to 100 bar. A 4-20 mA HART output is standard. For hazardous gas lines, ATEX Zone 1 or Zone 2 certification is available on request.
Steam measurement is where most sourcing portal listings fall short. Wet steam wears the bluff body and changes the K-factor. If your steam line runs at 10 bar and 185 °C, mention the degree of superheat or the condensate return rate. That detail helps us confirm whether a vortex meter with integral PT100 temperature compensation is enough or if you need a pressure transmitter paired with a flow computer.
Direct manufacturer versus a global sourcing portal
H
Silver Automation Instruments is based in Nanjing, China. We ship to industrial end users and distributors in Southeast Asia, Oceania, Latin America, Africa, and the Middle East. Most SME buyers are 10 to 100 person operations. They want one purchase order. They want a pre-shipment check and a calibration report that matches the serial number.
Price is not the only factor. An air flow meter that drifts after six months will cost more than the 15 percent to 25 percent you might save on a portal supplier. Ask for the calibration procedure. Ask about the sensor material. If the answer is vague, walk away.
What to send for a workable quotation
Send these data points with your inquiry. The list is short but it removes most of the back and forth.
Gas type or gas mixture, operating pressure in bar, operating temperature in °C, minimum and maximum flow in Nm3/h or kg/h, pipe size DN, pipe material, hazardous area classification, output signal preference, and target country for delivery.
If you do not have all the data, send the compressor power and the total line pressure. We can work from there. But the final quote will need the actual flow range. Most engineers skip this part and later receive a meter that is oversized. An oversized thermal mass meter at low velocity may read zero because the sensor does not see enough cooling.
FAQ: Air Flow Meter Sourcing and Technical Support
Which air flow meter is best for compressed air monitoring?
For compressed air at 7 bar to 10 bar with pipe sizes DN25 to DN300, thermal mass flow meters are usually the most practical. They measure mass flow directly and do not need separate pressure or temperature compensation.
Can one meter handle nitrogen and CO2?
Yes, but the meter must be calibrated or configured for the gas composition. A thermal mass meter calibrated for nitrogen will not read CO2 correctly without a correction factor. Send the gas mixture when you request a quote.
What pipe sizes do you cover?
Inline thermal mass meters start at DN15. Insertion thermal mass meters cover DN80 to DN300. Vortex flow meters cover DN25 to DN200 with flange or wafer connections. Larger line sizes can be quoted as special items.
Do your meters work in ATEX Zone 1 gas environments?
Yes. We supply ATEX Zone 1 and Zone 2 versions for both thermal mass and vortex meters. Specify the gas group and temperature class when you send your inquiry.
How do I compare quotes from air flow meter manufacturers?
Compare the flow range, turndown ratio, output signal, calibration certificate, sensor material, and delivery time. Do not compare only the unit price. A quote with no calibration data is not the same product.
Contact Silver Automation Instruments
Send your gas type, pressure (bar), temperature (°C), pipe size (DN), and flow range for a quotation. You can reach Silver Automation Instruments by Tel: +86-25-68650347, Whatsapp: +86-25-52155837, WeChat: +86 15365082610 or visit flow-meter.com.au.